控制阀标准汇总（二）

分享到：

ANSI/FCI 91-1-1997

控制阀门密封的质量标准

(Standard for Qualification of Control Valve Stem Seals)

ANSI/UL 753-1996

消防装置用自动供水控制阀的警报附件

(Alarm Accessories for Automatic Water-Supply Control Valves for Fire-Protection Service)

BS EN 60534-2-5-2003

工业过程控制阀.流通能力.通过有段间恢复功能的多段控制阀的流体流量的校准公式

(Industrial-process control valves - Flow capacity - Sizing equations for fluid flow through multistage control valves with interstage recovery)

ASTM F 1985-1999

气力操作的球形控制阀标准规范

(Standard Specification for Pneumatic-Operated, Globe-Syle, Control Valves)

BS EN 60534-3-2-2001

工业过程控制阀.尺寸.蝶形阀除外的转式控制阀的端面距

(Industrial-process control valves - Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves)

BS ISO 15407-2-2003

气压传动.五气口方向控制阀,规格18mm和26mm.有任选电接头的安装接口

(Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Mounting interface surfaces with optional electrical connector)

BS ISO 12238-2001

气压液动.方向控制阀门.转换时间的测量

(Pneumatic fluid power - Directional control valves - Measurement of shifting time)

BS ISO 5599-1-2001

气压液动.五通方向控制阀.不带电连接器的安装接口表面

(Pneumatic fluid power - Five-port directional control valves - Mounting interface surfaces without electrical connector)

BS ISO 5599-2-2001

气压液动.五通方向控制阀.任选电气连接器的安装接口面

(Pneumatic fluid power - Five-port directional control valves - Mounting interface surfaces with optional electrical connector)

BS EN 60534-6-2-2001

工业过程控制阀.定位器装到控制阀的安装细则.旋转传动装置上安装的定位器

(Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators)

BS EN 1074-5-2001

供水阀门.适用性和专用要求的试验.控制阀门

(Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Control valves)

BS EN 60534-8-3-2000

工业流程控制阀.噪声问题.控制阀的空气动力噪声预报法

(Industrial-process control valves - Noise considerations - Control valve aerodynamic noise prediction method)

BS EN 60534-2-3-1998

工业过程控制阀.流量.试验程序

(Industrial-process control valves - Flow capacity - Test procedures)

BS EN 60534-8-1-2001

工业过程控制阀.噪声问题.通过控制阀的动力噪声的实验室测量

(Industrial-process control valves - Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves)

BS EN 60534-3-1-2000

工业过程控制阀.尺寸.带法兰的两路、球型、直立式控制阀门的面对面尺寸和带法兰的两路、球型、角度控制阀门

(Industrial-process control valves - Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle patter)

BS EN 1349-2000

工业处理控制阀门

(Industrial process control valves)

BS ISO 15407-1-2000

18mm和26mm五气口气动方向控制阀.无电插头的安装界面

(Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Mounting interface surfaces without electrical connector)

BS ISO 11727-1999

气动流体力学.控制阀和其它元件的控制机械装置和气门的识别

(Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components)

BS EN 60534-3-3-1998

工业过程控制阀.尺寸.对接焊接,两向,球型,垂直模式控制阀的末端对末端尺寸

(Industrial-process control valves - Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves)

BS EN 60534-2-1-1999

工业过程控制阀 .流容.安装条件下液流规模方程

(Industrial-process control valves - Flow capacity - Flow capacity - Sizing equations for fluid flow under installed conditions)

BS ISO 6263-1997

液压传动.补偿式流量控制阀.装配面

(Hydraulic fluid power - Compensated flow-control valves - Mounting surfaces)

BS ISO 10770-2-1998

液压传动.电模式液压控制阀.第2部分:三向流动控制阀的试验方法

(Hydraulic fluid power - Electrically modulated hydraulic control valves - Test methods for three-way directional flow control valves)

BS ISO 10770-1-1998

液压传动.电模式液压控制阀.第1部分:四向流动控制阀的试验方法

(Hydraulic fluid power - Electrically modulated hydraulic control valves - Test methods for four-way directional flow control valves)

BS EN 60534-6-1-1998

工业过程控制阀 .控制阀调节器连接用安装元件.直线传动装置上调节器的安装

(Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on linear actuators)

BS ISO 7790-1998

液压传动.规格为03和05型的四油口标准设计叠阀和四油口定向控制阀.紧固尺寸

(Hydraulic fluid power - Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 - Clamping dimensions)

EN 60534-8-1-2000

工业过程控制阀　第8部分：噪声的考虑　第1节：气动流流径控制阀产生的噪声的实验室测量

Industrial-process control valves - Part 8: Noise consideration; Section 1: Laboratory measurement of noise generated by hydrodynamic aerodynamic flow through control valves (IEC 60534-8-1:1986)

EN 60534-8-4-1994

工业过程控制阀　第8部分：噪声问题　第4节：流动产生的噪声的预测

Industrial-process control valves - Part 8: Noise considerations - Section 4: Prediction of noise generated by hydrodynamic flow (IEC 60534-8-4:1994)

EN 60534-8-3-2000

工业流程控制阀　.第8-3部分　噪声问题　通过控制阀的动力噪声预测法

Industrial-process control valves - Part 8-3: Noise considerations; Control valve aerodynamic noise prediction method (IEC 60534-8-3:2000)

EN 1074-5-2001

供水阀门 目的要求的适应性和合适的认证试验 第5部分：控制阀门

Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5: Control valves

EN 60534-3-1-2000

工业过程控制阀　第３－１部分：尺寸　法兰双通球形直型控制阀的端面间距尺寸和有法兰双通球型角型控制阀的

Industrial-process control valves - Part 3-1: Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves (IEC 60534-3-1:2000)

EN 60534-2-1-1998

工业过程控制阀　第2－1部分：流通能力　安装条件下流体流量的校准公式

Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions (IEC 60534-2-1:1998)

EN 60534-1-1993

工业过程控制阀　第1部分　控制阀术语和一般考虑

Industrial-process control valves - Part 1: Control valve terminology and general considerations (IEC 60534-1:1987)

EN 60534-3-2-2001

工业过程控制阀　第３部分：尺寸　第２节：无法兰控制阀（薄型蝶阀除外）的端面间距尺寸

Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves (IEC 60534-3-2:2001)

EN 60534-3-3-1998

工业过程控制阀　第三部分：尺寸　对接焊接　两向　球型　垂直模式控制阀的末端对末端尺寸

Industrial-process control valves - Part 3-3: Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves (IEC 60534-3-3:1998)

EN 60534-6-1-1997

工业过程控制阀　第6－1部分：定位器联到控制阀执行机构的安装细则　第1节：直线传动装置上调节器的安装

Industrial-process control valves - Part 6: Mounting details for attachment of positioners to control valves - Section 1: Positioner mounting on linear actuators (IEC 60534-6-1:1997)

EN 60534-6-2-2001

工业过程控制阀　第6－2部分：定位器联到控制阀执行机构的安装细则　环形执行机构定位器

Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves; Positioner mounting on rotary actuators (IEC 60534-6-2:2000)

EN 60534-8-2-1993

工业过程控制阀　第8部分　噪声考虑　第2节通过控制阀的流体产生的噪声的实验室测量报法

Industrial-process control valves- Part 8: noise consideration- Section 2: laboratory measurement of noise generated by hydrodynamic flow through control valves (IEC 60534-8-2:1991)

EN 60534-2-3-1998

工业过程控制阀　第２部分：流通能力　第３节：试验规程

Industrial-process control valves - Part 2-3: Flow capacity - Test procedures (IEC 60534-2-3:1997)

prEN 13959-2000

公称压力在DN6至DN250（含DN250）的防污染控制阀　E族A、B、C和D型

Anti-pollution check valves DN 6 to DN 250 inclusive - Family E, type A, B, C and D

prEN 60534-4-1998

工业过程控制阀　第４部分：检验和常规试验　草案

IEC 60534-4: Industrial-process control valves - Part 4: Inspection and routine testing

EN 1349-2000+AC-2001

工业加工控制阀门

Industrial process control valves

EN 60534-2-5-2003

工业加工控制阀　第2-5部分：流量　 通过带级间恢复多级控制阀的流体尺寸方程　

Industrial-process control valves - Part 2-5: Flow capacity; Sizing equations for fluid flow through multistage control valves with interstage recovery (IEC 60534-2-5:2003) / Note: Endorsement notice

BS ISO 4401-1996

液压传动.四油口定向控制阀.装配面

(Hydraulic fluid power - Four-port directional control valves - Mounting surfaces)

BS EN 60534-1-1989

工业过程控制阀 .第1部分:控制阀术语和一般考虑

(Industrial-process control valves - Industrial-process control valves - Control valve terminology and general considerations)

BS EN 60534-8-4-1994

工业过程控制阀.第8部分:噪声问题.第4节.流动产生的噪声的预报

(Industrial-process control valves - Noise considerations - Prediction of noise generated by hydrodynamic flow)

BS EN 60534-8-2-1991

工业过程控制阀.第8部分:噪声考虑.第2节:通过控制阀的流体产生的噪声的实验室测量

(Industrial-process control valves - Noise considerations - Laboratory measurement of noise generated by hydrodynamic flow through control valves)

BS 6494-4-1989

液压阀的安装面.第4部分:03和05规格的四孔组件排气阀、模数组阀和方向控制阀夹紧尺寸规范

(Hydraulic fluid power valve mounting surfaces - Specification for clamping dimensions of four-part, size 03 and 05, modular stack valves and directional control valves)

BS 5793-4-1987

工业过程控制阀.第4部分:检验和例行试验规范

(Industrial-process control valves - Specification for inspection and routine testing)

BS 5944-4-1984

液压动力系统和部件所产生的空气噪音的测量.第4部分:流量和压力控制阀声功率级的测定方法

(Measurement of airborne noise from hydraulic fluid power systems and components - Method of determining sound power levels from valves controlling flow and pressure)

BS 5793-5-1984

工业过程控制阀.第5部分:标记规范

(Industrial-process control valves - Specification for marking)